Tekin HotWire 2.0 ESC Programmer

Tekin HotWire 2.0 ESC Programmer. Part number TEKTT1451. Tekin HotWire 2.0 ESC programmer for Windows and Android devices, with data logging, HV BEC settings and firmware updates.

This item drop ships direct to you same day with tracking!

Unlock the full potential of your Tekin speed control with the HotWire 2.0, connect to a host of devices running Windows or Android Operating Systems and leverage the processing power of these devices to fine tune performance. The HotWire provides access to additional tools such as data logging, adjustable high-voltage BEC settings and many more in-depth tuning options. The HotWire also lets you network with other users to share tuning tips and entire track/condition specific profiles with friends. Team Driver setup files are available to all, right off the Tekin website! Best of all, the HotWire lets you download software as it is developed and upload the newest firmware to your speed control - you get unrestricted access to Tekin's latest and newest performance mods!

Available on PC and some Android devices, on board Data Logging with the HotWire brings you all the info you need to know about your last run! Record a few laps or a pull down the drag strip and review the data on a PC or Android device immediately afterward. Monitor ESC, battery and motor performance so you can get the most out of your system and keep your setup tuned perfectly!

"What devices", you ask? Most devices that can host a USB connection provided they are running the appropriate Operating System.

Tekin HotWire runs on the following Windows/Android operating systems (USB): Android 3.1 & Up, Windows XP, Windows Vista (32 bit & 64 bit), Windows 7 (32 bit & 64 bit), Windows 8* (32 bit & 64 bit) *Requires .NET 3.5, Windows 10* (32bit & 64bit) *Requires .NET 3.5 (To run on Mac try using Bootcamp or Parallels)

Features

• Connect via USB to PC, Netbook and most Android Devices
• Connects to all Tekin ESCs and Servos via Receiver Wire
• Connects to GEN2+ ESCs via Data Port using TT3825 Adapter
• Tune ESC and Servos to your liking
• Datalogging Capabilities
• LED Status Indicator
• USB Cable Included
• Free HotWire Software and ESC/Servo Firmware updates
• 180-Day Factory Warranty
• Lifetime Support
• Access to Team Driver Speed Control Profiles
• Create, Download and Share Custom Speed Control Profiles

ESC Programmable Features*

• Update ESC Firmware
• Create, Save, Load and Share Custom ESC Profiles
• Drag Brake (0-100 steps)
• Brake Strength (0-100 steps)
• Brake Minimum (0-30 steps)
• Active Drag (ON/OFF)
• Active Braking (0-6 steps)
• Brake Frequency (750Hz - 12kHz)
• RPM Intelligent Brake Strength (0-10 steps)
• Throttle Minimum (0-30 steps)
• Throttle Frequency (2kHz - 12kHz)
• Torque Limiter (0-10 steps)
• Reverse Speed (0-100 steps)
• Reverse Delay (0-2 seconds)
• Neutral Width (0-100 steps)
• Push Control (0-100 steps)
• Timing Profiles 5 Preset - 2 Custom
• Locked Spec Mode
• Boost (0-55 steps)
• Boost RPM Range (user programmable)
• Turbo (0-50 steps)
• Turbo Delay (0-2 seconds)
• Turbo Ramp (1-10 steps)
• Sensored Only Mode
• Dual Drive Mode
• Motor Type
• Brushless Modes - FWD Only / FWD-REV / FWD-REV Delay / REV Motor Rotation
• Brushed Modes - FWD Only / FWD-REV / FWD-REV Delay
• Voltage Cutoff - 2S, 3S, Custom Per Cell
• 1S LiPo Mode
• Fan ON/AUTO Modes

*Comprehensive list of features, not all are available on every Tekin ESC. Refer to each ESC product page Features section for a list of settings available.

Servo Programmable Features

• Update Servo Firmware
• Feel - Mild to Aggressive
• Speed Limit
• Torque (0-100%)
• Torque Delay
• Direction - Normal / Reverse
• Center Point
• Travel
• Soft Starting Speed & Torque
• Max Temp Alarm
• Low Voltage Alarm
• Over Voltage Alarm
• Bind Relief
• Fail Safe Speed and Position
• Set Custom Servo Name

Data Logging Graphs

• Throttle
• PWM
• Voltage
• Battery Ripple
• ESC Temperature
• RPM
• Motor Temperature
• Set a Sample Rate, view logs at multiple resolutions, customize the display and save data logs for comparing!

*Data Logging is not available on iOS